5.0 KiB
MiniMax A1 Mini physical qualification plan
This plan is the gate from virtual qualification to a functional sailing prototype. It applies to the validated reduced model in MiniMaxHull.FCStd and its production STL files.
Required hardware
- Bambu Lab A1 Mini
- PLA filament
- Two TowerPro SG90 servos
- WEMOS LOLIN ESP32-S2 Mini v1.0.0
- The intended battery and switch/wiring harness
- Digital scale with at least 0.1 g resolution
- Calipers with at least 0.1 mm resolution
- Shallow water tank
- Syringe or low-pressure leak-test equipment
- Small weights for ballast and CG adjustment
Gate 1: printed-part inspection
Record the actual material, slicer, profile, layer height, wall count, infill, support settings, and measured mass of every printed part.
PASS criteria:
- No through-wall defects in the hull, hatch, seal lip, keel, rudder, mast, or boom.
- Hull and hatch fit without forced deformation.
- Hatch seal clearance is not less than 0.15 mm at any measured point and does not bind.
- Rudder stock, keel, mast, and boom fit their modeled interfaces.
- No stringing or support residue prevents servo or electronics installation.
FAIL criteria:
- Any leak path through the hull or hatch sealing region.
- Any crack, delamination, or dimensional defect affecting assembly.
- Any control surface that binds or cannot reach its full modeled travel.
Gate 2: mass and center of gravity
Measure each item separately, then the fully assembled dry boat with the intended battery and wiring.
Record:
- Hull and hatch mass.
- Keel and ballast mass.
- Rudder and stock mass.
- Mast, boom, and sails mass.
- Two servo masses.
- ESP32, battery, switch, wiring, and connectors.
- Total dry mass.
- Longitudinal, transverse, and vertical CG relative to the CAD datum.
PASS_WITH_REVIEW target:
- Total mass: 140–155 g.
- Nominal design target: 145 g.
- CG must remain within the modeled ballast/trim envelope.
- Any difference greater than 5 g from the target requires rerunning the mass/CG sensitivity check.
Gate 3: electronics and servo installation
Install both real SG90 servos and the real ESP32 board before sealing the hatch.
PASS criteria:
- Servo bodies and connectors do not contact the hull, tray, hatch, or seal lip.
- Rudder and sheet pushrods move from -60 to +60 degrees without binding.
- No pushrod collision with the ESP32 tray or opposite servo.
- USB access and battery replacement remain possible without damaging wiring.
- Servo power wiring is strain-relieved and cannot enter the pushrod paths.
FAIL criteria:
- Any binding, stalled servo, inaccessible connector, or interference under the hatch.
Gate 4: leak and immersion test
Perform the test without electronics powered.
- Install the hatch and all intended seals.
- Add a dry absorbent indicator inside the hull.
- Float the empty hull for 5 minutes.
- Repeat with the fully assembled dry mass.
- Perform gentle trim changes and repeat.
PASS criteria:
- No visible water ingress.
- Absorbent indicator remains dry.
- Hatch does not lift or shift under handling.
A successful leak test does not qualify the boat for powered operation until the wiring penetrations are tested as installed.
Gate 5: static flotation and trim
Use fresh water and measure the waterline at the bow, stern, and both sides.
Record:
- Total assembled mass.
- Water temperature if available.
- Bow, stern, port, and starboard waterline heights.
- Heel angle at rest.
- Freeboard at the lowest point.
PASS_WITH_REVIEW criteria:
- The boat supports the measured assembled mass without taking water over the coaming.
- Trim is repeatable after removing and replacing the boat.
- No persistent list caused by battery, servo, or ballast placement.
- The measured waterline is compared with the CAD design waterline of 23 mm.
Any waterline difference greater than 2 mm requires updating the mass/CG model before sailing.
Gate 6: unpowered control and rig test
Before placing the boat on open water:
- Verify full rudder travel manually.
- Verify sheet travel manually.
- Check mast and boom retention.
- Check keel and ballast retention.
- Check rudder stock stiffness.
- Check that the hatch remains sealed while the rig is loaded by hand.
Do not apply full sail loads if any mast, keel, rudder, or hatch interface is loose.
Gate 7: powered shallow-water test
Use a shallow controlled area with retrieval access.
- Test receiver/controller operation with the boat supported.
- Test each servo independently.
- Test failsafe behavior.
- Float without sail load and verify steering.
- Add sail load only after the previous checks pass.
- Record trim, turning response, servo temperature, and any water ingress.
STOP immediately for loss of control, servo overheating, water ingress, structural movement, or battery displacement.
Qualification outcome
The model may be called physically qualified for competition only when Gates 1–7 pass and the measured values are added to the machine-readable report. Until then the repository status remains PASS_WITH_REVIEW; the current virtual results are not a substitute for these tests.